RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: davesteemke
Showing results 1 to 12 of 12
Search took 0.10 seconds.
Forum: Kit Building
05-20-2006, 08:53 PM
Replies: 723
Views: 118,457
Posted By davesteemke

RE: Goldberg Ultimate 10-300 build

That plane is gorgeous. U must have spent a lot of time on it, it shows. How does she fly?
Forum: Kit Building
05-18-2006, 12:13 AM
Replies: 723
Views: 118,457
Posted By davesteemke

RE: Goldberg Ultimate 10-300 build

Glad to hear you were able to locate some ailerons, tuwood. Thanks 4 the pictures & info . of the bottom wing mount. I'll try and reinforce the same area. I'll probably have a few "hot" landings the...
Forum: Kit Building
05-15-2006, 02:25 AM
Replies: 723
Views: 118,457
Posted By davesteemke

RE: Goldberg Ultimate 10-300 build

Thanks 4 your service Maekju. Hope everything goes well.
I've been assembling my new (thanks to tuwood's generosity) wheel pants and cowl. I've finished the primer coat and tomorrow will start on...
Forum: Kit Building
05-04-2006, 12:39 AM
Replies: 723
Views: 118,457
Posted By davesteemke

RE: Goldberg Ultimate 10-300 build

Thanks 4 the info. I've spent quite a bit of $ on this project, trying to see if i can use what I got. Your pictures helped greatly. I'm going to go out to the shop and see what i can do. Thanks...
Forum: Kit Building
05-03-2006, 06:45 PM
Replies: 723
Views: 118,457
Posted By davesteemke

RE: Goldberg Ultimate 10-300 build

I have a Question concerning the cowl. I have a OS FS-III 1.20 4 stroke. Sideways mounted. I'm going to have to cut a small opening on the cowl for the heads to fit. But what should I do for the...
Forum: Kit Building
04-26-2006, 03:03 PM
Replies: 723
Views: 118,457
Posted By davesteemke

RE: Goldberg Ultimate 10-300 build

Thankx, I didn't want to put a hole in my fuselage anyway, thank you for your reply.
Dave
Forum: Kit Building
04-26-2006, 04:20 AM
Replies: 723
Views: 118,457
Posted By davesteemke

RE: Goldberg Ultimate 10-300 build

I have a question. I'm installing a Dubro Kwik-Fuel Valve on my ultimate, but am not sure which lines I should connect to it. I'm using a OS FS-120 III with pump, and my tank has three lines. Thankx
Forum: Kit Building
04-17-2006, 01:37 PM
Replies: 723
Views: 118,457
Posted By davesteemke

RE: Goldberg Ultimate 10-300 build

Mr. Underwood, I filed that wire down a bit. And it went right in. Amazed, thinking it was a fluke, I pulled it out and it went right back in. Thanks 4 saving me the aggravation.
Dave
Forum: Kit Building
04-14-2006, 11:42 PM
Replies: 723
Views: 118,457
Posted By davesteemke

RE: Goldberg Ultimate 10-300 build

Thanks, I'll try that.
Thanks 4 Your Time,
Dave
Forum: Kit Building
04-13-2006, 11:26 PM
Replies: 723
Views: 118,457
Posted By davesteemke

RE: Goldberg Ultimate 10-300 build

Any tips on an easy way to get the wire through the holes on the top wing, I'm pretty much done, and am now assembling the airplane. It was so much easier without the covering, what happened? Also,...
Forum: Kit Building
04-11-2006, 12:25 AM
Replies: 723
Views: 118,457
Posted By davesteemke

RE: Goldberg Ultimate 10-300 build

Thanks 4 the info tuwood ,
Dave
Forum: Kit Building
04-09-2006, 07:59 PM
Replies: 723
Views: 118,457
Posted By davesteemke

RE: Goldberg Ultimate 10-300 build

Read through thread, found some great ideas for strengthening my new plane. I've already installed some aluminum landing gear, and strengthened my wingsMy setup is as follows:CG Ultimate 10-300, OS...
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.