RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: jesse2357
Showing results 1 to 14 of 14
Search took 0.01 seconds.
Forum: RC Jets
04-10-2018, 06:15 PM
Replies: 1,631
Views: 335,240
Posted By jesse2357

I cut the fg a little towards the bottom of the...

I cut the fg a little towards the bottom of the retract tub and used my hemostats to install the blind nut.
Forum: RC Jets
04-09-2018, 04:16 PM
Replies: 1,631
Views: 335,240
Posted By jesse2357

I put blind nuts on my gear, I also printed a...

I put blind nuts on my gear, I also printed a plastic spacer to space the gear even with the bottom of the wing. As for the Clevis I add a jam nut to tighten that up.
Forum: RC Jets
03-16-2018, 02:45 PM
Replies: 1,631
Views: 335,240
Posted By jesse2357

Well finally got mine back in after turbine...

Well finally got mine back in after turbine issues. I upgraded to the k85. flys great with it. Much more authority then the 70. a little tweaking and she'll be ready for the season. It's funny I had...
Forum: RC Jets
03-15-2018, 07:48 PM
Replies: 1,631
Views: 335,240
Posted By jesse2357

I was referring to when the plane is off and the...

I was referring to when the plane is off and the batteries are still plugged in
Forum: RC Jets
03-14-2018, 12:49 PM
Replies: 1,631
Views: 335,240
Posted By jesse2357

It's the brakes that drain the power. Same thing...

It's the brakes that drain the power. Same thing happens on my Avanti mini when I leave them plugged in over night.
Forum: RC Jets
02-09-2018, 10:35 AM
Replies: 1,631
Views: 335,240
Posted By jesse2357

They are adjustable if you put them on a slider...

They are adjustable if you put them on a slider then you add as much or as little as you like. Or you can put them on a the accelerometers of a Jeti TX like I do and just tilt your TX to stop. I set...
Forum: RC Jets
02-08-2018, 12:32 PM
Replies: 1,631
Views: 335,240
Posted By jesse2357

Your end points adjust brake force. No...

Your end points adjust brake force. No directional force though. I wish
Forum: RC Jets
02-08-2018, 12:14 PM
Replies: 1,631
Views: 335,240
Posted By jesse2357

The red controller for the jp retracts has no...

The red controller for the jp retracts has no adjustments other then brake force as far as I could figure out. The 2 door outputs one is regular and the other is reversed. I had to move to the inner...
Forum: RC Jets
02-07-2018, 09:25 PM
Replies: 1,631
Views: 335,240
Posted By jesse2357

The trail of the wheel does matter when using...

The trail of the wheel does matter when using weight to balance. It matters so much that your suppose to tie wrap your gear so it doesn’t move at all and effect your readings. Also the plane being...
Forum: RC Jets
02-07-2018, 11:41 AM
Replies: 1,631
Views: 335,240
Posted By jesse2357

Here is my Xicoy measurements now if you look I...

Here is my Xicoy measurements
now if you look I pushed everything towards the tail cause everyone said they were nose heavy. My turbine I pushed behind the former. I also mounted my pump and switch...
Forum: RC Jets
02-04-2018, 06:54 PM
Replies: 1,631
Views: 335,240
Posted By jesse2357

I had assist turned off the flights. I tested my...

I had assist turned off the flights. I tested my 7 assist in a turbo bush master 3d plane and found it to perform flawless.
Forum: RC Jets
02-04-2018, 06:09 PM
Replies: 1,631
Views: 335,240
Posted By jesse2357

I'm 205mm back from where the wing meets the...

I'm 205mm back from where the wing meets the fuselage, I know there is some debate on where that is, My cg is 70mm in front of the center of the main gear wheel. CG was spot on from the limited...
Forum: RC Jets
02-04-2018, 05:48 PM
Replies: 1,631
Views: 335,240
Posted By jesse2357

I maidened mine today, first flight uneventful...

I maidened mine today, first flight uneventful one of the easiest jet maidens I've ever had Second flight started off great.. I really wished I would have put ion the 85 the 70 just doesn't move this...
Forum: RC Jets
01-04-2018, 08:24 PM
Replies: 1,631
Views: 335,240
Posted By jesse2357

Anyone know if the cg at 200 to 205 is with gear...

Anyone know if the cg at 200 to 205 is with gear down or up?
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.