RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Truckracer
Showing results 1 to 9 of 9
Search took 0.01 seconds.
Forum: Gas Engines
02-23-2019, 12:36 PM
Replies: 32
Views: 2,145
Posted By Truckracer

Have you seen one of the later cylinders? I've...

Have you seen one of the later cylinders? I've had it from several sources they are not the same as what was used years ago on the Brison / Taurus / Fox / FPE engines. I've never had one in my hands...
Forum: Gas Engines
02-23-2019, 12:18 PM
Replies: 32
Views: 2,145
Posted By Truckracer

I would have seen it when I cleaned up the parts...

I would have seen it when I cleaned up the parts for reassembly. I always polished the prop drive hub before reinstall ..... except the anodized ones of course. I still cleaned them thoroughly. Oh...
Forum: Gas Engines
02-23-2019, 12:10 PM
Replies: 32
Views: 2,145
Posted By Truckracer

Brison parts are available, you just have to do...

Brison parts are available, you just have to do some looking to find them and know what you are looking for. The Sachs, Dolmer, Makita parts were widely used in a number of different chainsaws and...
Forum: Gas Engines
02-23-2019, 12:02 PM
Replies: 32
Views: 2,145
Posted By Truckracer

Every Brison crank I have seen was straight (no...

Every Brison crank I have seen was straight (no taper). Strange that I have not run into one of the engines that used a tapered collet. For awhile a few years back, I bought and resold a few Brison...
Forum: Gas Engines
02-23-2019, 11:16 AM
Replies: 32
Views: 2,145
Posted By Truckracer

These were very good and powerful engines in...

These were very good and powerful engines in their day and remain so today. As long as they are in good condition they will continue to run with the best of them well into the future. These engines...
Forum: Gas Engines
02-23-2019, 10:52 AM
Replies: 32
Views: 2,145
Posted By Truckracer

Gary was noted for changing things up a bit...

Gary was noted for changing things up a bit between production runs. I still like the engines though! Just curious, how did he maintain the hub in one location for timing with the split collet? I...
Forum: Gas Engines
02-23-2019, 09:33 AM
Replies: 32
Views: 2,145
Posted By Truckracer

https://cimg6.ibsrv.net/gimg/www.rcuniverse.com-vb...

https://cimg6.ibsrv.net/gimg/www.rcuniverse.com-vbulletin/640x853/brison_hub_front_17f2d81e027fb0b8675d87bc2ca2b02d8fe645b9.jpg...
Forum: Gas Engines
02-20-2019, 08:51 PM
Replies: 32
Views: 2,145
Posted By Truckracer

Can’t answer your question without knowing what...

Can’t answer your question without knowing what the engine is. If Brison, the prop driver slides on the shaft with a key. They usually have a bit of loctite holding everything tight
Forum: Gas Engines
02-20-2019, 07:47 PM
Replies: 32
Views: 2,145
Posted By Truckracer

Did you mean Brison 3.2 engine?

Did you mean Brison 3.2 engine?
Showing results 1 to 9 of 9


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.