RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: smalley46
Showing results 1 to 11 of 11
Search took 0.10 seconds.
Forum: Kit Building
03-23-2007, 06:21 PM
Replies: 3,645
Views: 708,131
Posted By smalley46

RE: Top Flite 1/7 P-51 Build

Thanks mikemedic and IB Buck. I will press on with finishing the wing before i start carving for the retracts.
Forum: Kit Building
03-22-2007, 09:17 PM
Replies: 3,645
Views: 708,131
Posted By smalley46

RE: Top Flite 1/7 P-51 Build

For flying Beagle et al.
I have gone with the 440 struts as planned but swapped the Spring/Air retracts for the 701 retract which is also a air up/spring down. i did have problems with the 44o's at...
Forum: Kit Building
03-13-2007, 08:08 PM
Replies: 3,645
Views: 708,131
Posted By smalley46

RE: Top Flite 1/7 P-51 Build

I'm going to jump back in here after a delay of a couple months. Been doing more flying and occasional crashing than building. I was going to use Spring Air retracts with Robostrut 440 series so i...
Forum: Kit Building
01-29-2007, 07:42 PM
Replies: 3,645
Views: 708,131
Posted By smalley46

RE: Top Flite 1/7 P-51 Build

anyones in particular mustang?
Forum: Kit Building
01-29-2007, 07:08 PM
Replies: 3,645
Views: 708,131
Posted By smalley46

RE: Top Flite 1/7 P-51 Build

I believe a few people have touched on the subject but I was wondering if people could tell me what they are using for servos in this plane.
Thanks
Forum: Kit Building
12-12-2006, 04:41 PM
Replies: 3,645
Views: 708,131
Posted By smalley46

RE: Top Flite 1/7 P-51 Build

I'm not planning on using functional doors. I'm going for something like the rare earth magnets as was mention in an earlier post. My goal is to have the wheel flush with the sheeting. I know people...
Forum: Kit Building
12-12-2006, 10:21 AM
Replies: 3,645
Views: 708,131
Posted By smalley46

RE: Top Flite 1/7 P-51 Build

I'm planning on using spring air 116 85 retracts and combining them with robart 7/16 robostruts 663L and R whose offset will handle 3 3/4 to 4 inch diameter wheels. I've talked with Bill at spring...
Forum: Kit Building
12-04-2006, 07:49 PM
Replies: 3,645
Views: 708,131
Posted By smalley46

RE: Top Flite 1/7 P-51 Build

ticketec or anyone else whose scale modeling the B or D model check out this link.

http://www.fourthfightergroup.com/resource/4th.html
Forum: Kit Building
12-04-2006, 06:21 PM
Replies: 3,645
Views: 708,131
Posted By smalley46

RE: Top Flite 1/7 P-51 Build

Cpig....the model 116 is the 85 degree.

Ticketec...how do you do that stenciling???? WOW!!!!!!
thanks for the primer on washout.
Forum: Kit Building
11-30-2006, 09:05 PM
Replies: 3,645
Views: 708,131
Posted By smalley46

RE: Top Flite 1/7 P-51 Build

For Cpig...
What spring -airs did you use??? 85 or 90? Can they accomodate a 4" wheel? They have a 25% sale on now and although I was going to wait until I built the wing if they are good i would...
Forum: Kit Building
11-30-2006, 06:03 PM
Replies: 3,645
Views: 708,131
Posted By smalley46

RE: Top Flite 1/7 P-51 Build

I guess I'm the new kid on the block. Want to thank everyone who has contributed to this P51 build. I have been reading this forum closely for the last week. I've been flying rc for six months and...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.