Welcome to Club SAITO !
The fg11 does sound good were you running a straight pipe or a muffler?
Pix of the fg57 will be up as soon as i get my camera back.
ps sammy you watch out for that sr telemaster plane,they can be a bit tricky to handle and sometimes bite back
Pix of the fg57 will be up as soon as i get my camera back.
ps sammy you watch out for that sr telemaster plane,they can be a bit tricky to handle and sometimes bite back
LOL! I would put my 330 on floats BUT! Don't want to have to dive to the bottom to retrieve my tween. Think the tele, is no big deal. Like the Sig Sr, Kadet better, just like thet big wing on the Telemaster.
We are lucky to have an asphalt strip that is a bit low near one end so when it rains heavy you get some deep puddles to takeoff through on full throttle.The water vortex of the prop tips is good to watch but you can hear the saito grinding away a bit,it drops a few revs and sharpens the tips of apc props and if it rains heavy while flying i always worry about water hitting my tx but it's worth it to watch the prop and plane with water bouncing off the airframe and getting sprayed everywhere by the prop as well.Should i think about floats sammy?...be a bit hard on them in summer tho i reckon the saito singles would have enough grunt to launch it.
Senior Member
I assume people have done CH ignitions on their Saito's on here? I have a FA 200R3 i plan on sending to Adrian at CH ignitions in a couple of days for the gas conversion. Engine has not had any fuel ran through it yet it is new. Is there a difference is performance and power and sound between gas and nitro? Sorry I'm kinda new to the conversions.
When comparing CDI glow fuel to gas, it's about 20-25% advantage for glow fuel if the CDI glow fuel conversion is tuned properly.
Senior Member
I'm just going from memory but if I recall correctly, CHT measured between the rocker boxes @ the rear was 20°F hotter W/CDI/glow fuel compared to GI & CDI/e-85 was an additional 40°F hotter than the CDI/glow fuel combo. I abandoned the e-85 idea because it us not readily available in my area & when it is, it is often only 60% ethanol in colder months. The glow fuel carburetor was also way too sensitive.
Since the blend I was using was most likely the lower % ethanol blend, the temperatures I observed would be close to what a straight gasoline conversion would run.
l don't know what happened there Oldfart? I hit the wrong button? It all wen't away? Anyway. l did fly off a paved runway in Hot Springs. Thats about 50Mils away, Now l live in Lt, Rock and we fly off of grass. lt's a old landfill that is on top of a hill but when it rains, it turns to Quagmire (bad mud) our parking lot is small and kinda at a angel and if your not lucky, you in up in the woods (No Fun) I go to HS sometimes, I miss the paved runway and my buddies, just cost me a lot to drive over there for one day and my X is running around there some where?? Every time l here a car l think it's her! (BAD NEWS) She found where l was parking my trailer after l left her and broke in to it and cost me about $10,000 (Stomped Everything) had to start over. Sucked! l had some new planes that l have not got to fly yet. Also cost me $5,000 to get my name off of stuff, what rely pi**'d me off is that she stole my dog! So, YA, I get kinda of pi**y at some women! I have been flying for over 40Yrs and no woman is going to stop that! The one l have now is the best! She buys me plane's and even comes to the field! BUT! Back to flying, when it rains at our field, it in's up into everything, makes a mess! Sometimes it pays to stay home.
Senior Member
Join Date: Sep 2004
Location: Lawrenceville,
GA
Posts: 152
Likes: 0
Received 0 Likes
on
0 Posts
But I am running with the muffler cause I need the nose weight.
If the weather holds out, I'll try it again today with a 13/6 prop.
I'm looking for the thrust of the 12/8 but with some braking effect, That darn 7 lb Smith has some *big* inertia to overcome on landing.
Nick
My Feedback: (3)
My Feedback: (3)
My Feedback: (22)
Join Date: Jan 2003
Location: palm harbor,
FL
Posts: 2,232
Likes: 0
Received 0 Likes
on
0 Posts
I recently got a hanger 9 ultras til 60.hard to come by these days but I got one and unlike my last one from a number of years back I got a 91 mounted.i have been flying electric but got nostalgic for my greasers.my wife isn't thrilled but I am.anyway the only prop I had lying around was an app 14 the fuel is good but 15 percent.what are you guys using typically on the 91 satio for props and are u buying 20 percent.
Question on first start of my 100 GK
It has been run before, but the guy said not well. What should I set the needles to for first run. Also what can I use to extend the needle past the cowl? Something else, when I mounted the spinner back plate and prop, I noticed I dont have many threads left.
The spinner bolts to teh lockdown nut, which I need to get since the ones that come with the spinner have the wrong threads, so out of the two from Tower, which one do I use for this one?
http://www3.towerhobbies.com/cgi-bin...2&I=LXHMF3&P=K
http://www3.towerhobbies.com/cgi-bin...2&I=LXB957&P=K
It has been run before, but the guy said not well. What should I set the needles to for first run. Also what can I use to extend the needle past the cowl? Something else, when I mounted the spinner back plate and prop, I noticed I dont have many threads left.
The spinner bolts to teh lockdown nut, which I need to get since the ones that come with the spinner have the wrong threads, so out of the two from Tower, which one do I use for this one?
http://www3.towerhobbies.com/cgi-bin...2&I=LXHMF3&P=K
http://www3.towerhobbies.com/cgi-bin...2&I=LXB957&P=K
Your crankshaft should be 8x1.25 mm thread.
Wind your lsn out till it is flush with the lower bevel on the throttle arm and wind the hsn out four turns from fully closed.
ps you can use piano wire for the needle ext.
Wind your lsn out till it is flush with the lower bevel on the throttle arm and wind the hsn out four turns from fully closed.
ps you can use piano wire for the needle ext.
Last edited by Rudolph Hart; 06-22-2014 at 05:56 PM.
Senior Member
My Feedback: (3)
cloudancer03, I ran 10-15% in my 91, mounting a 13/8 3-blade for ground clearance and reduced roll effects on the Skybolt bipe, (14/8 2-blade overpowered the ailerons on the low wing only during vertical maneuvers). Both props should work fine.
IMO, if you need any higher nitro content look for a larger motor.
IMO, if you need any higher nitro content look for a larger motor.
Where did you find that old relic? I asked Mike @ Sig if they had any thoughts on reissuing that kit, and he said NOPE. A friend of mine has one that he bought already built, and I wanted to build one too.
Senior Member
Join Date: Sep 2004
Location: Lawrenceville,
GA
Posts: 152
Likes: 0
Received 0 Likes
on
0 Posts
After much thought...
I don't remember seeing such a critter.
And short of soldering a 90 degree brass tube to it, I'm clueless.
Nick
PS. The 13/6 performed nicely on the Smith. I put a new vid of it in the previously linked Smith thread.
I don't remember seeing such a critter.
And short of soldering a 90 degree brass tube to it, I'm clueless.
Nick
PS. The 13/6 performed nicely on the Smith. I put a new vid of it in the previously linked Smith thread.
Last edited by taildragger1589; 06-23-2014 at 07:31 AM.
Senior Member
Before my laptop took a crap, I had a link to a site that carried the 90° breather nipples.
I think I found them by searching on some R/C car sites.
Senior Member
Join Date: Sep 2004
Location: Lawrenceville,
GA
Posts: 152
Likes: 0
Received 0 Likes
on
0 Posts
My Feedback: (22)
Join Date: Jan 2003
Location: palm harbor,
FL
Posts: 2,232
Likes: 0
Received 0 Likes
on
0 Posts
Hi a .actually I have seen a couple .one was ebay and the other was rc groups.just type sig liberty sport and see where it leads.in my case a club member I really enjoy flying with put one in my car.it was in the bones.i dropped it off my bench and had to Re build the tail which turned out to be a good thing as the original was weak.the local hobby shop had the cover it laying around and sold it to me for the price of monokote.i in
stalled an on surpass 91.hope to maiden it soon.actually is my first bipe.
stalled an on surpass 91.hope to maiden it soon.actually is my first bipe.