Welcome to Club SAITO !
My Feedback: (16)
RE: Welcome to Club SAITO !
ORIGINAL: Tom Jones
Hobbsy, Is Lynda your wife? Hope she is getting better. My Prayers are with her for a complete recovery, God willing. Take care Tom
Hobbsy, Is Lynda your wife? Hope she is getting better. My Prayers are with her for a complete recovery, God willing. Take care Tom
I've called his home but didn't get an answer.
My Feedback: (17)
Join Date: Sep 2002
Location: Nokomis FL
Posts: 145
Likes: 0
Received 0 Likes
on
0 Posts
RE: Welcome to Club SAITO !
Hi all,
Finally getting around to ask about joining the CLUB. I have a 30, 50, 56, 72, 82, 91, 100, (2) 120 dual plug pumpers, (2) 150s. I fix engines for the guys here in Sarasota and probably have had another 50 Saitos apart. I love all my Saitos - the 50 and 91 have more hours on them than I can count. Several sets of bearings for each, but both have the original ring!
Jim
Finally getting around to ask about joining the CLUB. I have a 30, 50, 56, 72, 82, 91, 100, (2) 120 dual plug pumpers, (2) 150s. I fix engines for the guys here in Sarasota and probably have had another 50 Saitos apart. I love all my Saitos - the 50 and 91 have more hours on them than I can count. Several sets of bearings for each, but both have the original ring!
Jim
My Feedback: (11)
RE: Welcome to Club SAITO !
I am hereby requesting membership into your fine organization... I am the proud owner of a 125 golden knight, a 120 and a FS90TS twin. I am hoping that the membership dues are not substantial. Does the initiation ceremony involve hazing?
I am looking for some exhaust pipes for the FS90TS... anyone got something laying around?
I am looking for some exhaust pipes for the FS90TS... anyone got something laying around?
My Feedback: (3)
RE: Welcome to Club SAITO !
ORIGINAL: on_your_six
I am hereby requesting membership into your fine organization... I am the proud owner of a 125 golden knight, a 120 and a FS90TS twin. I am hoping that the membership dues are not substantial. Does the initiation ceremony involve hazing?
I am hereby requesting membership into your fine organization... I am the proud owner of a 125 golden knight, a 120 and a FS90TS twin. I am hoping that the membership dues are not substantial. Does the initiation ceremony involve hazing?
697 ZachB10
698 shaggy48
699 SRQFlyer
700 on_your_six
I would put #700 in my sig line if it were me!
Senior Member
Join Date: Nov 2006
Location: Macarthur,
WV
Posts: 163
Likes: 0
Received 0 Likes
on
0 Posts
RE: Welcome to Club SAITO !
Double ought seven could stand for wins ties losses. I think I'd stick to 700 just in case.
Cherokee flyer, let the hazing begin.
Cherokee flyer, let the hazing begin.
RE: Welcome to Club SAITO !
ORIGINAL: Hobbsy
Jim, here's the .30 arrangement.
Jim et al, Lynda is back in the hospital, one of her kidneys stopped working and loaded her up with uric acid causing violent convulsions and near comotose. They got here awake yesterday but she is still very weak.
Jim, here's the .30 arrangement.
Jim et al, Lynda is back in the hospital, one of her kidneys stopped working and loaded her up with uric acid causing violent convulsions and near comotose. They got here awake yesterday but she is still very weak.
RE: Welcome to Club SAITO !
ORIGINAL: w8ye
I've had a Saito 82A about 4 yrs. I decided to make a 82B out of it.
I bought
Back plate
Crankcase
Cam cover
Carb screw set
Cam pivot shaft
I had to steal a cam cover gasket from my Saito FG20 collection and I had to make a gasket for the back plate as Horizon doesn't have gaskets yet.
I made the back plate gasket from the cover flap of the package that the back plate came in. I cut the inside circle and slipped it over the back plate and then mounted the back plate and trimed off the outside. You need a gasket back there to keep the cam cover from rubbing on the crankshaft pin.
After getting it together I ran the engine on the test bench and it runs just as good as it did before I changed everything.
I've had a Saito 82A about 4 yrs. I decided to make a 82B out of it.
I bought
Back plate
Crankcase
Cam cover
Carb screw set
Cam pivot shaft
I had to steal a cam cover gasket from my Saito FG20 collection and I had to make a gasket for the back plate as Horizon doesn't have gaskets yet.
I made the back plate gasket from the cover flap of the package that the back plate came in. I cut the inside circle and slipped it over the back plate and then mounted the back plate and trimed off the outside. You need a gasket back there to keep the cam cover from rubbing on the crankshaft pin.
After getting it together I ran the engine on the test bench and it runs just as good as it did before I changed everything.
My Feedback: (16)
RE: Welcome to Club SAITO !
ORIGINAL: Old Fart
I like your sense of humour friend.Caqn we get a 100 or 125 cylinder on an 82a which already equals the old 91 in performance or am i dreaming a bit?
ORIGINAL: w8ye
I've had a Saito 82A about 4 yrs. I decided to make a 82B out of it.
I bought
Back plate
Crankcase
Cam cover
Carb screw set
Cam pivot shaft
I had to steal a cam cover gasket from my Saito FG20 collection and I had to make a gasket for the back plate as Horizon doesn't have gaskets yet.
I made the back plate gasket from the cover flap of the package that the back plate came in. I cut the inside circle and slipped it over the back plate and then mounted the back plate and trimed off the outside. You need a gasket back there to keep the cam cover from rubbing on the crankshaft pin.
After getting it together I ran the engine on the test bench and it runs just as good as it did before I changed everything.
I've had a Saito 82A about 4 yrs. I decided to make a 82B out of it.
I bought
Back plate
Crankcase
Cam cover
Carb screw set
Cam pivot shaft
I had to steal a cam cover gasket from my Saito FG20 collection and I had to make a gasket for the back plate as Horizon doesn't have gaskets yet.
I made the back plate gasket from the cover flap of the package that the back plate came in. I cut the inside circle and slipped it over the back plate and then mounted the back plate and trimed off the outside. You need a gasket back there to keep the cam cover from rubbing on the crankshaft pin.
After getting it together I ran the engine on the test bench and it runs just as good as it did before I changed everything.
The cylinder that comes on a 82 has the same bore as the 100 cylinder but uses 91 valves.
Using a 125 cylinder would complicate things as you would have to use the 125 piston and then what about rod length?
My Feedback: (153)
Join Date: Oct 2007
Location: greenville,
MS
Posts: 433
Likes: 0
Received 0 Likes
on
0 Posts
RE: Welcome to Club SAITO !
hey anyone started their saito single backwards? i had my starter reversed at the field today and started my 56 in reverse, i flew the plane several times after with no problems think i did ant harm?
Join Date: Jan 2010
Location: Fort Collins, Colorado
Posts: 226
Likes: 0
Received 0 Likes
on
0 Posts
RE: Welcome to Club SAITO !
while retuning my 100 it ran backwards for about a minute
I had trouble shutting it down. Don't think it caused any harm
And is usually just improper tuning. Usually too rich
.
I had trouble shutting it down. Don't think it caused any harm
And is usually just improper tuning. Usually too rich
.
My Feedback: (153)
Join Date: Oct 2007
Location: greenville,
MS
Posts: 433
Likes: 0
Received 0 Likes
on
0 Posts
RE: Welcome to Club SAITO !
well just thought i would check, w8ye? apparently not was not the response i was expecting? something like no it should be fine, or you might want to check a push rod or something else. this is the only saito i own so i dont know the ins and outs of them so i come to you guys. mark
My Feedback: (16)
RE: Welcome to Club SAITO !
You didn't hurt it. It will be fine
Worst case scenario is that it would mess up the o ring where the intake manifold goes into the head but if it ran afterwards, there is no problem
Worst case scenario is that it would mess up the o ring where the intake manifold goes into the head but if it ran afterwards, there is no problem
RE: Welcome to Club SAITO !
ORIGINAL: mistermnkim
hey anyone started their saito single backwards? i had my starter reversed at the field today and started my 56 in reverse, i flew the plane several times after with no problems think i did ant harm?
hey anyone started their saito single backwards? i had my starter reversed at the field today and started my 56 in reverse, i flew the plane several times after with no problems think i did ant harm?